PROFESSIONAL AUDIO EQUIPMENT Multimedia Amplifier M1 User Manual & Installation GuideMultimedia Amp M1 AUDAC
9 Overview Input 7-10 (4x St. Line) INPUT 7-10 (FRONT) INPUT 7-10 (REAR) Input level VU bar (Pre Fader) Routin
10Overview Output Zones OUTPUT ZONES 1-4 (FRONT) OUTPUT ZONES 1-4 (REAR) Output Level VU-Bar Two band tone control Zone output
11Overview DATA Control Ports DATA CONTROL PART (Rear) Ethernet connection (RJ45) Wall Panel Outlets (RS485) Serial Control Port (R
12 Getting Started When turning on the power, the M1 start-up procedure will take place. This will take about 30sec.. Selected zones will light up g
13Routing settings can be saved by pressing together the ‘ch7’ and ‘ch8’ buttons on the front panel of the M1. Hold down the 2 buttons for a few seco
14 Wire up the System The AUDAC M1 amplifier is very easy in use. Following cable specs must be followed to guarantee a correct operation: 1. Speake
15SubAmplifier 1Amplifier 2L RL+RXLR, RightXLR, LeftXLR, LeftXLR, RightMicrophone 1Microphone 2XLRXLRRLR LEthernetWireless RouterEthernetNotebookWire
16Bridge Mode The M1 Multimedia amplifier can also be set in bridged mode (300W / 8ohm) by setting some jumpers on the inside of the M1. This has to
17Remote Control Interface To use the remote control interface, the M1 has to be plugged in to an Ethernet LAN network with a standard (straight) net
18Standard Web Based User Interface LOG-IN SCREEN: When you surf to the webpage of the M1, you will see the logon screen of the M1. Default the IP ad
AUDAC PROFESSIONAL AUDIO EQUIPMENT User Manual & Installation Guide AUDAC http://www.audac.be [email protected]
19CONTROL SCREEN: If you press “enter” after typing the correct username and password, you get access to the control screen of the M1. After logging
20CONFIGURATION SCREEN: This window will be opened after pressing the “Configuration” button in the control window. (Default Username: audac, default
21Lite Web Based User interface PURPOSE: The purpose of the Lite Web Based User Interface is to offer easy access to the basic functions of the M1 an
22ROOM CONFIGURATION SCREEN: In this screen you can assign an input source to the selected room, change the output volume ( = zone output volume) or
23NAME CONFIGURATION SCREEN: This screen can be activated by pressing 3 times on the “Audac” logo in the “Room Configuration Screen”. Here you can ch
24 Wall Mounted Control Panels (Optional) The M1 Multimedia amplifier can be equipped with wall mounted control panels on each zone output. A zone
25 Jumper settings for zone output selection A B C D E ABCDEZone outputJJJJJ 1JJJJ 2JJJ J 3JJJ 4J = set jumper
26 Additional Information M1 Technical specifications Sensitivity Microphone input -60/-20 dB 600 Ohm balanced Line i
27Personal Notes
2 INTRODUCTION...
3 Introduction This section describes briefly the functionality of the M1amplifier. he M1 Multimedia Amplifier is developed as a “all in one”, flexi
4 Environment Do not place this unit in an enclosed environment such as a bookshelf or closet. Ensure there is adequate ventilation to cool the un
5 Safety Requirements Always handle the unit with care. Only use a grounded socket outlet and a power cord with grounding plug to plug in the unit.
6 Pin connections on Connectors XLR (input, output): pin1=Ground, pin2= hot(s+), pin3=cold(s-) Cinch: tip= Signal (left or right), Ring= Ground RJ4
7 Overview front and rear panel of the M1 FRONT: REAR: Chapter 2
8 Overview Inputs 1-6 (Mic./St. Line) INPUT 1-6 (FRONT) INPUT 1-6 (REAR) Routing Buttons + LED: To rout Input to Zone 1-4 Inp
Kommentare zu diesen Handbüchern